Tuesday, April 5, 2016

Brother DCP7030 Trouble Error Codes

Brother DCP7030 Trouble Error Codes
Brother DCP7030 Trouble Error Codes


CodeDescriptionCauses
50Replacement time of the drum unit• Replace the drum unit with a new one.
56Fuser cover opened• Check if the Fuser cover is closed correctly. Harness connection failure of back cover switch ASSY Eject actuator failure Eject sensor PCB ASSY failure Main PCB failure
58Fuser unit failure (Stand ready in the given time)
59Fuser unit failure
5AHVPS PCB ASSY failureHVPS PCB failure (Developing bias voltage failure) HVPS PCB ASSY harness connection failure HVPS PCB failure Main PCB failure
5BNew toner detecting lever malfunctionNew toner detection switch harness connection failure New toner detection switch failure Main PCB failure
63Toner cartridge is at the end of life.• Gently shake the toner cartridge from side to side and install it again. • Replace the toner cartridge.
Harness connection failure of new toner sensor harness ASSY. Harness connection failure of toner sensor PCB unit ASSY. New toner sensor harness ASSY failure (Toner empty) Toner sensor PCB unit ASSY failure. Main PCB failure
67Toner of the toner cartridge is low• Prepare a new toner cartridge. If the toner is empty, Replace it.
68Fuser unit failure
(The side thermistor detects higher temperature than the specified value.)
69Fuser unit failure
(The side thermistor detects lower temperature than the specified value.)
6AFuser unit failure
(The side thermistor does not detect 60°C within the specified time.)
6BFuser unit failure
(The center thermistor does not detect 100°C within the specified time.)
6CFuser unit failure
(The center thermistor detects higher temperature than the specified value.)
6DFuser unit failure
(The center thermistor detects lower temperature than the specified value.)
6EFuser unit failure
(The center thermistor does not detect temperature rising within the specified time.)
CodeDescriptionCauses
6FFuser unit failure
(The center and side thermistors detect extremely high temperature.)
71Polygon motor failure
(Cannot detect the period signal of the polygon mirror motor.)
72BD beam detecting sensor malfunctionLaser unit harness connection failure. Laser unit failure. Main PCB failure
75Machine cooling down insideThe temperature inside the machine is too high. Both ends of the heat roller are at different temperatures. The paper media is replaced with different Paper size media.
76Fuser unit failure
(The center thermistor detects rapidly rising temperature.)
77Fuser unit failure
Fuser error code failure (The error history of the fuser unit is deleted.)
78Fuser unit failure
(The temperature sensor of the fuser unit is broken.)
79No detection of the internal temperature thermistorHarness connection failure of internal temperature thermistor Internal temperature thermistor failure Main PCB failure
7ANo detection of main motor lock signalMain motor failure Main PCB failure
7BMain PCB failure
7DDirt on drum unit• Clean the corona wire of the drum unit. • Replace the drum unit with a new one.
Dirt or dust on drum unit electrodes HVPS PCB failure Main PCB failure
7FFax paper setting mismatch
(The setting paper becomes besides the A4/Letter/Legal/Folio.)
80Fax paper size is small
(The registration rear sensor detected the paper that is smaller than the letter size.)
84Paper jam in rear of the machine
(It is detects by the eject sensor)
88Paper jam inside the machine
(It is detects by the registration rear sensor)
CodeDescriptionCauses
6FFuser unit failure
(The center and side thermistors detect extremely high temperature.)
71Polygon motor failure
(Cannot detect the period signal of the polygon mirror motor.)
72BD beam detecting sensor malfunctionLaser unit harness connection failure. Laser unit failure. Main PCB failure
75Machine cooling down insideThe temperature inside the machine is too high. Both ends of the heat roller are at different temperatures. The paper media is replaced with different Paper size media.
76Fuser unit failure
(The center thermistor detects rapidly rising temperature.)
77Fuser unit failure
Fuser error code failure (The error history of the fuser unit is deleted.)
78Fuser unit failure
(The temperature sensor of the fuser unit is broken.)
79No detection of the internal temperature thermistorHarness connection failure of internal temperature thermistor Internal temperature thermistor failure Main PCB failure
7ANo detection of main motor lock signalMain motor failure Main PCB failure
7BMain PCB failure
7DDirt on drum unit• Clean the corona wire of the drum unit. • Replace the drum unit with a new one.
Dirt or dust on drum unit electrodes HVPS PCB failure Main PCB failure
7FFax paper setting mismatch
(The setting paper becomes besides the A4/Letter/Legal/Folio.)
80Fax paper size is small
(The registration rear sensor detected the paper that is smaller than the letter size.)
84Paper jam in rear of the machine
(It is detects by the eject sensor)
88Paper jam inside the machine
(It is detects by the registration rear sensor)
CodeDescriptionCauses
ECFan performance malfunction
F8Battery connection failure
F9Maintenance mode 74 Non-decision
(Inputting omission of the customizing code.)


Download Service Manual,Error Codes,
Download Laptop,download drivers, download laptop Drivers,ALL LAPTOP DRIVER. DELL DRIVERS, HP DRIVERS, TOSHIBA DRIVERS, ACER DRIVERS , LENOVO DRIVERS , SONY DRIVERS, SUMSUNG DRIVERS, ASUS DRIVERS,Acer Drivers, Mutoh Drivers,Apple Drivers,OCE Drivers,Brother Drivers,OKI Drivers,Canon Drivers Olivetti Drivers,Duplo Drivers,Panasonic Drivers,Encad-Kodak Drivers,Printronix Drivers,Epson Drivers,Ricoh Drivers,HP Drivers,Riso Drivers,KIP Drivers,Konica Drivers,Samsung Drivers,Konica-Minolta Drivers,Sanyo Drivers,Kyocera-Mita Drivers,Sharp Drivers,Lexmark Drivers,Sony Drivers,LG Drivers,Star '
A Note S37SP Drivers for Windows XP & Vist,
Drivers,Mimaki Drivers,Toshiba Drivers,Minolta Drivers,Various Drivers,Muratec Drivers,Zebra Drivers

No comments:

Post a Comment