Brother DCP8060 Trouble Error Codes

Brother DCP8060 Trouble Error Codes

Code	Description	Causes
56	The fuser cover is opened.
57	Duplex jam	- Paper is remained. - Main PCB defective - Duplex reverse gear damaged - Duplex solenoid defective
5A	High-voltage power supply PCB malfunction
5B	New toner sensor lever error (New toner sensor stays on)	New toner actuator lever broken New toner sensor defective
5C	Optional lower tray (LT-5300) error	Two or more optional lower trays are installed.
5D	Duplex printing cannot be implemented.
60	Recording paper is stacked too much in the eject section.	Stacker sensor defective
68	Side thermistor high temperature error	Side thermistor short circuit
69	Side thermistor low temperature error	Side thermistor break
6A	Heater warming-up timeout error. (Heater does not reach 60 within 12 second.)	Thermistor defective Halogen lamp defective
6B	Heater warming-up timeout error. (Heater does not reach 100 within 9 second.)	Thermistor defective Halogen lamp defective
6C	Heater temperature exceeds the maximum high temperature. (270 or more is detected for 1sec.)	Thermistor defective Power supply PCB defective
6E	Heater temperature does not go up enough.	Halogen lamp defective Power supply PCB defective
6F	Heater hard limiter operates.	Thermistor defective. Power supply PCB defective
71	Scanner motor does not synchronize with the reference clock. Laser unit defective Main PCB defective

Code	Description	Causes
72	Cannot detect Beam Detect signal.	Laser unit defective Main PCB defective
73	The drum unit is not mounted.
74	Toner empty	Toner sensor defective Toner empty
75	In casing temperature error.	In casing temperature sensor defective
76	Heater overheats.	Thermistor in the fuser unit defective PS PCB unit defective Main PCB defective
77	The power supply is turned off when the error 76 or 78 occurs.
78	Temperature of the heater does not rise.	Poor connection in the harness of the halogen lamp Halogen lamp defective Thermistor defective PS PCB unit defective Main PCB defective
79	Thermistor in the machine defective	Extremely high or low temperature inside the machine
7A	Main motor does not synchronize with the reference clock.	Main PCB defective Main motor defective
7B	ASIC error on the main PCB.
7D	Dust on the drum.	Corona wire is dirty.
80	At the start of FAX message printing, the controller detects that paper is smaller than A4 size in width.	Paper smaller than the specified size loaded in the paper tray Main PCB defective
81	Recording paper jam.
82	Recording paper jam in paper pull-in operation
83	Recording paper jam. (The registration sensor comes ON too early in the paper feeding operation.)	Paper is not correctly set in the paper tray Separation pad damaged Registration sensor actuator unhooked Main PCB defective

Code	Description	Causes
84	Recording paper jam. (The registration sensor stays ON after completion of paper ejection operation.)	The paper ejection roller does not rotate correctly Foreign materials in the paper path. Registration sensor actuator caught on the surrounding parts Registration sensor broken Main PCB defective
85	No paper tray1 loaded.	Tray 1 is not closed completely.
86	No paper tray2 loaded.	Tray 2 is not closed completely.
88	Recording paper jam. (Even after paper pulling-in operation, the registration sensor is still OFF.)	Recording paper not loaded correctly Registration sensor broken Separation pad damaged Objects, such as bits of paper or chips, are in the paper tray or paper tray Paper pick up roller defective Paper feed motor broken Main PCB defective
8A	Jam tray1
8B	Jam tray2
8C	Jam MP tray
A1	Front cover opened.	Hook of the front open switch on the front cover broken
A2	Document length exceeding the scan limitation. During scanning, 90 cm or longer of a document is detected. During document feeding or ejecting, 400 cm or longer of a document is detected.	Front open switch broken Document jam
A3	The document rear sensor does not come ON during document pull-in operation.	Document jam Document rear sensor actuator caught on the surrounding parts Document rear sensor broken
A4	50% or more faulty of white level data.
A5	FAX scanning failure. (1st time)	CCD defective White-level reference film stained in the scanner cover Main PCB defective
A6	FAX scanning failure. (retry)
AA	The document cover is opened when the ADF is used.	Document cover sensor defective
AC	Less than 50% faulty of white level data.

Code	Description	Causes
AF	The scanner is locked.	Scanner lock lever is not released. Scanner lock lever defective
B1	Dark level offset data level error for scanning.	CCD defective Main PCB defective
B2	Gain control data level error for scanning.	CCD defective Main PCB defective
B3	Scan area left edge detection error.	Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B4	Scan area right edge detection error.	Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B5	Horizontal scanning edge reduction detection error in scanning area setting.	Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B6	Horizontal scanning edge enlargement detection error in scanning area setting	Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B7	A/D converter reference voltage error (at High level).	Main PCB defective
B8	A/D converter reference voltage error (at Low level).
B9	Light emission intensity error of the LED array (Exceeding the upper limit).	CCD defective Main PCB defective
BB	White level data error.	CCD defective Main PCB defective
BD	Black level data error.	CCD defective Main PCB defective
BE	Scan starting edge detection error.	Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
BF	Duplex scanning cannot be implemented due to too long document.	- The document is too long. - ADF front sensor 2 defective
D0 … DF	Modem error.	Main PCB defective

Code	Description	Causes
E6	Write error in EEPROM.	Main PCB defective
E8	Data scanning error during transmission.	CCD defective Main PCB defective
EA	Document removed at phase B.	Document front sensor actuator caught on the surrounding parts Sensor PCB defective Main PCB defective

Download Service Manual,Error Codes,
Download Laptop,download drivers, download laptop Drivers,ALL LAPTOP DRIVER. DELL DRIVERS, HP DRIVERS, TOSHIBA DRIVERS, ACER DRIVERS , LENOVO DRIVERS , SONY DRIVERS, SUMSUNG DRIVERS, ASUS DRIVERS,Acer Drivers, Mutoh Drivers,Apple Drivers,OCE Drivers,Brother Drivers,OKI Drivers,Canon Drivers Olivetti Drivers,Duplo Drivers,Panasonic Drivers,Encad-Kodak Drivers,Printronix Drivers,Epson Drivers,Ricoh Drivers,HP Drivers,Riso Drivers,KIP Drivers,Konica Drivers,Samsung Drivers,Konica-Minolta Drivers,Sanyo Drivers,Kyocera-Mita Drivers,Sharp Drivers,Lexmark Drivers,Sony Drivers,LG Drivers,Star '

A Note S37SP Drivers for Windows XP & Vist,

Drivers,Mimaki Drivers,Toshiba Drivers,Minolta Drivers,Various Drivers,Muratec Drivers,Zebra Drivers