Tuesday, April 5, 2016

Brother DCP8065DN Trouble Error Codes

Brother DCP8065DN Trouble Error Codes
Brother DCP8065DN Trouble Error Codes


CodeDescriptionCauses
56The fuser cover is opened.
57Duplex jam- Paper is remained. - Main PCB defective - Duplex reverse gear damaged - Duplex solenoid defective
5AHigh-voltage power supply PCB malfunction
5BNew toner sensor lever error (New toner sensor stays on)New toner actuator lever broken New toner sensor defective
5COptional lower tray (LT-5300) errorTwo or more optional lower trays are installed.
5DDuplex printing cannot be implemented.
60Recording paper is stacked too much in the eject section.Stacker sensor defective
68Side thermistor high temperature errorSide thermistor short circuit
69Side thermistor low temperature errorSide thermistor break
6AHeater warming-up timeout error. (Heater does not reach 60 within 12 second.)Thermistor defective Halogen lamp defective
6BHeater warming-up timeout error. (Heater does not reach 100 within 9 second.)Thermistor defective Halogen lamp defective
6CHeater temperature exceeds the maximum high temperature. (270 or more is detected for 1sec.)Thermistor defective Power supply PCB defective
6EHeater temperature does not go up enough.Halogen lamp defective Power supply PCB defective
6FHeater hard limiter operates.Thermistor defective. Power supply PCB defective
71Scanner motor does not synchronize with the reference clock.
Laser unit defective Main PCB defective
CodeDescriptionCauses
72Cannot detect Beam Detect signal.Laser unit defective Main PCB defective
73The drum unit is not mounted.
74Toner emptyToner sensor defective Toner empty
75In casing temperature error.In casing temperature sensor defective
76Heater overheats.Thermistor in the fuser unit defective PS PCB unit defective Main PCB defective
77The power supply is turned off when the error 76 or 78 occurs.
78Temperature of the heater does not rise.Poor connection in the harness of the halogen lamp Halogen lamp defective Thermistor defective PS PCB unit defective Main PCB defective
79Thermistor in the machine defectiveExtremely high or low temperature inside the machine
7AMain motor does not synchronize with the reference clock.Main PCB defective Main motor defective
7BASIC error on the main PCB.
7DDust on the drum.Corona wire is dirty.
80At the start of FAX message printing, the controller detects that paper is smaller than A4 size in width.Paper smaller than the specified size loaded in the paper tray Main PCB defective
81Recording paper jam.
82Recording paper jam in paper pull-in operation
83Recording paper jam. (The registration sensor comes ON too early in the paper feeding operation.)Paper is not correctly set in the paper tray Separation pad damaged Registration sensor actuator unhooked Main PCB defective
CodeDescriptionCauses
84Recording paper jam. (The registration sensor stays ON after completion of paper ejection operation.)The paper ejection roller does not rotate correctly Foreign materials in the paper path. Registration sensor actuator caught on the surrounding parts Registration sensor broken Main PCB defective
85No paper tray1 loaded.Tray 1 is not closed completely.
86No paper tray2 loaded.Tray 2 is not closed completely.
88Recording paper jam. (Even after paper pulling-in operation, the registration sensor is still OFF.)Recording paper not loaded correctly Registration sensor broken Separation pad damaged Objects, such as bits of paper or chips, are in the paper tray or paper tray Paper pick up roller defective Paper feed motor broken Main PCB defective
8AJam tray1
8BJam tray2
8CJam MP tray
A1Front cover opened.Hook of the front open switch on the front cover broken
A2Document length exceeding the scan limitation. During scanning, 90 cm or longer of a document is detected. During document feeding or ejecting, 400 cm or longer of a document is detected.Front open switch broken Document jam
A3The document rear sensor does not come ON during document pull-in operation.Document jam Document rear sensor actuator caught on the surrounding parts Document rear sensor broken
A450% or more faulty of white level data.
A5FAX scanning failure. (1st time)CCD defective White-level reference film stained in the scanner cover Main PCB defective
A6FAX scanning failure. (retry)
AAThe document cover is opened when the ADF is used.Document cover sensor defective
ACLess than 50% faulty of white level data.
CodeDescriptionCauses
AFThe scanner is locked.Scanner lock lever is not released. Scanner lock lever defective
B1Dark level offset data level error for scanning.CCD defective Main PCB defective
B2Gain control data level error for scanning.CCD defective Main PCB defective
B3Scan area left edge detection error.Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B4Scan area right edge detection error.Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B5Horizontal scanning edge reduction detection error in scanning area setting.Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B6Horizontal scanning edge enlargement detection error in scanning area settingBlack markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
B7A/D converter reference voltage error (at High level).Main PCB defective
B8A/D converter reference voltage error (at Low level).
B9Light emission intensity error of the LED array (Exceeding the upper limit).CCD defective Main PCB defective
BBWhite level data error.CCD defective Main PCB defective
BDBlack level data error.CCD defective Main PCB defective
BEScan starting edge detection error.Black markings on the white-level reference film inside the scanner top cover. CCD defective Main PCB defective
BFDuplex scanning cannot be implemented due to too long document.- The document is too long. - ADF front sensor 2 defective
D0 … DFModem error.Main PCB defective
CodeDescriptionCauses
E6Write error in EEPROM.Main PCB defective
E8Data scanning error during transmission.CCD defective Main PCB defective
EADocument removed at phase B.Document front sensor actuator caught on the surrounding parts Sensor PCB defective Main PCB defective


Download Service Manual,Error Codes,
Download Laptop,download drivers, download laptop Drivers,ALL LAPTOP DRIVER. DELL DRIVERS, HP DRIVERS, TOSHIBA DRIVERS, ACER DRIVERS , LENOVO DRIVERS , SONY DRIVERS, SUMSUNG DRIVERS, ASUS DRIVERS,Acer Drivers, Mutoh Drivers,Apple Drivers,OCE Drivers,Brother Drivers,OKI Drivers,Canon Drivers Olivetti Drivers,Duplo Drivers,Panasonic Drivers,Encad-Kodak Drivers,Printronix Drivers,Epson Drivers,Ricoh Drivers,HP Drivers,Riso Drivers,KIP Drivers,Konica Drivers,Samsung Drivers,Konica-Minolta Drivers,Sanyo Drivers,Kyocera-Mita Drivers,Sharp Drivers,Lexmark Drivers,Sony Drivers,LG Drivers,Star '
A Note S37SP Drivers for Windows XP & Vist,
Drivers,Mimaki Drivers,Toshiba Drivers,Minolta Drivers,Various Drivers,Muratec Drivers,Zebra Drivers

No comments:

Post a Comment